| About |
|---|
| 10-3003 is a new high bond strength epoxy adhesive formulated for ease in handling and convenience for the end user. This system has a non-critical mix ratio and adjustable flexibility. 10-3003 is also very safe to use due to the absence of harmful solvents and toxic chemicals in the formulation. 10-3003 yields high peel strength and excellent tensile strength. It also has outstanding thermal shock, impact and vibration resistance. This high performance epoxy adhesive exhibits outstanding physical, thermal, and electrical insulation properties. 10-3004 NC is available as a very low viscosity version of 10-3003. 10-3002 is available as a higher viscosity version of 10-3003. Features: Non-critical mix ratio Ability to adjust flexibility of bond line Outstanding thermal shock resistance Excellent chemical resistance Very good operating temperature range&& |
| Product Description | |
|---|---|
| Generic | 环氧树脂 |
| Material Status | Commercial: Active |
| Features | Thermal insulation,Good flexibility,Good bond,Good Tensile Strength,Good thermal shock resistance,Solvent resistance,Insulation,Agglomerability |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| bending strength | 352 | MPa | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 210 | J/m |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear coefficient of thermal expansion | |||
| MD | 5.0E-5 | 1/℃ | |
| Thermal conductivity coefficient | 0.43 | W/m/K |
| Thermosetting mixed viscosity | Nominal value | Unit | Test method |
|---|---|---|---|
| 25℃ | 15000 | cP |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| working temperature | -50.0 to 125 | ℃ |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| colour | Clear/Transparent | ||
| Weight Mix Ratio (PBW) | |||
| Part A | 100 | ||
| Part B | 100 | ||
| Density | |||
| 25℃ | 0.958 | g/cm³ | |
| 25℃ | 1.17 | g/cm³ | |
| viscosity | |||
| 25℃ | 6.0 | Pa·s | |
| 25℃ | 12 to 15 | Pa·s | |
| Curing time | |||
| 93℃ | 0.25 to 0.50 | hr | |
| 66℃ | 0.50 to 1.0 | hr | |
| 23℃ | 24 | hr | |
| storage stability | |||
| 25 ℃ | 90 | min |
| Cured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 72.4 | MPa | |
| Electrical strength | 22 | kV/mm | |
| Relative permittivity | |||
| 1 kHz | 3.11 | ||
| Volume resistivity | 1.1E+15 | ohms·cm | |
| Dissipation factor | 0.020 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Part B |
| 3. Part A |
| 4. 100 gram mass |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |