Polytron® P50N01LE

About
Polytron P50N01LE is Natural, 50% Long Glass Fiber Reinforced, Heat Stabilized,Reduced Emmision Behavior POLYPROPYLENE, The Glass Fibers are Chemically Coupled to the Polymer Matrix, The material is supplied in pellets that are typically 12mm in length. Fiber length is the length of the pellets. Typical applications include Structural Automotive Applications , For Passengersu0027 compartment parts,Interior Applications

About

Polytron P50N01LE is Natural, 50% Long Glass Fiber Reinforced, Heat Stabilized,Reduced Emmision Behavior POLYPROPYLENE, The Glass Fibers are Chemically Coupled to the Polymer Matrix, The material is supplied in pellets that are typically 12mm in length. Fiber length is the length of the pellets. Typical applications include Structural Automotive Applications , For Passengersu0027 compartment parts,Interior Applications

Product Description
Supplier	Ram-On
Generic	PP not specified
Material Status	Commercial: Active
Features	Low odor,Chemical coupling,Heat Stabilized
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.33	g/cm³	ISO 1183
Shrinkage rate
TD：2.0 mm	0.20 to 0.30	%
TD：2.0 mm	0.10 to 0.15	%

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
—	12500	MPa
70℃	8000	MPa
Tensile stress
—	135	MPa
150°C	100	MPa
Tensile strain
fracture	1.8	%
Fracture, 150 ℃	2.4	%
Bending modulus	12000	MPa	ISO 178
Bending stress	220	MPa	ISO 178

IMPACT	Nominal value	Unit
Charpy Notched Impact Strength
—	25	kJ/m²
-40℃	22	kJ/m²
Charpy Unnotch Impact strength
—	65	kJ/m²
-40℃	55	kJ/m²

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	158	℃	ISO 75-2/B
1.8 MPa, unannealed	157	℃	ISO 75-2/A
Melting temperature	168	℃	ISO 11357-3

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level
3.00 mm	HB		UL 94
Flammability	< 100	mm/min	FMVSS 302

Process Conditions
Injection	Nominal value	Unit	Test method
Temperature at the rear of the barrel	230 to 250	°C
Temperature in the middle of the barrel	230 to 250	°C
Front temperature of material barrel	230 to 250	°C
Mold temperature	50 to 70	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.