| About |
|---|
| APEX® 1003 is a Flexible Polyvinyl Chloride material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding. Important attributes of APEX® 1003 are: Flame Rated RoHS Compliant Typical applications include: Wire & Cable Engineering/Industrial Parts Electrical/Electronic Applications&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | PVC, not specified |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.35 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 1.0 to 1.2 | % | ASTM D955 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Continuous use temperature | 60.0 | ℃ | ASTM D794 |
| Embrittlement temperature | -35.0 | ℃ | ASTM D746 |
| 0.9 mm | 90.0 | ℃ | UL 746 |
| 1.4 mm | 90.0 | ℃ | UL 746 |
| 3.0 mm | 90.0 | ℃ | UL 746 |
| Relative temperature index | UL 746 | ||
| Electrical performance | UL 746 | ||
| 0.90 mm | 80.0 | ℃ | UL 746 |
| 1.40 mm | 90.0 | ℃ | UL 746 |
| 3.00 mm | 90.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Compared to the resistance to leakage and marking index | |||
| 3.00 mm | PLC 0 | UL 746 | |
| High Arc Burning Index (HAI) (3.0 mm) | PLC 1 | UL 746 | |
| Hot wire ignition (HWI) (3.0 mm) | PLC 2 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.90 mm | HB | UL 94 | |
| 1.40 mm | HB | UL 94 | |
| 3.00 mm | HB | UL 94 | |
| Extreme oxygen index | 24 | % | ASTM D2863 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 15 seconds | 79 | ASTM D2240 | |
| tensile strength | |||
| fracture | 10.5 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 260 | % | ASTM D638 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 179 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |