| About |
|---|
| DESCRIPTION: Epocast® 8623-A resin/Hardener 9861 epoxy syntactic is a two-part, core-filling compound with a soft paste consistency for easy extrusion through a 1/8-in. (3mm) nozzle. Epocast® 8623-A resin/Hardener 9861 epoxy syntactic is self-extinguishing and cures at room temperature, if desired. Elevated temperature cure or post cure will improve elevated temperature properties.&& |
| Product Description | |
|---|---|
| Supplier | Huntsman |
| Generic | 环氧树脂 |
| Material Status | Commercial: Active |
| Features | Self-extinguishing,Low density |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | ASTM D792 | ||
| — | 0.650 | g/cm³ | ASTM D792 |
| — | 0.700 | g/cm³ | ASTM D792 |
| — | 1.05 | g/cm³ | ASTM D792 |
| Solid content | 100 | % | ASTM D1644 |
| viscosity | ASTM D2393 | ||
| — | Paste | ASTM D2393 | |
| — | Soft-paste | ASTM D2393 | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Compression modulus | 1720 | MPa | ASTM D695 |
| compressive strength | |||
| 25℃ | 34.5 | MPa | ASTM D695 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Self extinguishing time | < 10.0 | sec | BMS 5-28 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Thermosetting components | |||
| resin | 按重量计算的混合比: 100 | ||
| Hardening method | 按重量计算的混合比: 20 |
| Thermosetting mixed viscosity | Nominal value | Unit | Test method |
|---|---|---|---|
| 25℃ | 18000 | cP | ASTM D2393 |
| Gelation time | |||
| 100 gms，25℃ | 40.0 to 60.0 | min | ASTM D2471 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Curing time | |||
| 25℃ | 1.0 | day | |
| Extrudability（1/8 inch nozzle at 80 psi） | 30.0 | g/min | |
| Tensile Lap Shear（etched al/al，25℃） | 11.0 | MPa | ASTM D1002 |
| Weight gain | ASTM D570 | ||
| Distilled water | 1.5 | % | ASTM D570 |
| Mil-M-5606，hydraulic fluid | 0.40 | % | ASTM D570 |
| Mil-S-3136，Type III test fluid：25℃ | 0.30 | % | ASTM D570 |
| Skydrol 500-A | 0.60 | % | ASTM D570 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Resin |
| 3. System |
| 4. Hardener |
| 5. on immersion – 24 hrs |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |