| About |
|---|
| The Evoprene COGEE range was specially developed to provide materials which will comould or coextrude to engineering thermoplastics (ETPs). This enables, for example, polyamide (nylon) handles or ABS housings to be given a solt touch feel whilst polycarbonate lenses can have gaskets moulded on to provide a weathertight product. The Evoprene COGEE grades are modified Kraton G based compounds. Many of the characteristics exhibited by the Evoprene G and Evoprene Super G ranges are shown by Evoprene COGEE compounds. However, they do have to be processed quite differently to obtain optimum bond strengths and performance characteristics.&& |
| Product Description | |
|---|---|
| Generic | SEBS |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Ozone resistance |
| Availabilitys | North America,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.930 | g/cm³ | ISO 2781 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 49 | ISO 868 | |
| abrasion resistance | 216 | mm³ | DIN 53516 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 4.00 | MPa | ISO 37 |
| 300% strain | 3.50 | MPa | ISO 37 |
| 100% strain | 1.80 | MPa | ISO 37 |
| Tensile strain | |||
| fracture | 470 | % | ISO 37 |
| tear strength | 22 | kN/m | ISO 34-1 |
| Compression deformation | ISO 815 | ||
| 23℃，72 hr | 43 | % | ISO 815 |
| 70℃，22 hr | 86 | % | ISO 815 |
| 100℃，22 hr | 92 | % | ISO 815 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Operating temperature | -30 to 60 | ℃ |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air (125 ℃, 336 hr) | -4.0 | % | ISO 1817 |
| Change in Tensile Strain at Break in Air（125℃，336 hr） | 2.0 | % | ISO 1817 |
| The rate of change of Shore hardness in air | |||
| 125℃，336 hr | -2.0 | ISO 1817 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Bond Strength | 1.14 | MPa | Internal Method |
| M-S Flow | 0.981 | MPa | Internal Method |
| Ozone resistance | |||
| 35℃ | No Cracks | ISO 1431-1 | |
| UV Rating（40℃） | No Visible Cracks or Crazing |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Proposed maximum recycled material ratio | 20 | % | |
| Barrel rear temperature | 250 to 270 | °C | |
| Barrel middle temperature | 250 to 270 | °C | |
| Barrel front temperature | 250 to 270 | °C | |
| Nozzle temperature | 250 to 270 | °C | |
| Processing (melt) temperature | 280 | °C | |
| Mold temperature | 30 to 60 | °C | |
| Injection speed | Fast | ||
| Vent depth | 0.020 to 0.050 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method Ba, Angle (Unnicked) |
| 3. 100 pphm/200 hrs/20% Strain |
| 4. 350 hrs |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |