| About |
|---|
| LOCTITE® PE 3142 Epoxy Resin forms a potting compound resin with high thermal conductivity when mixed with LOCTITE® PE 3165. This mixture forms a resilient, low exotherm, room temperature gel material that develops high Tg after exposure to elevated temperatures.&& |
| Product Description | |
|---|---|
| Supplier | Henkel |
| Generic | 环氧树脂 |
| Material Status | Commercial: Active |
| Features | Low Exotherm,Elastic,Thermal conductivity |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.62 | g/cm³ | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 90 | ASTM D2240 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | 84.0 | ℃ | ASTM D3418 |
| Linear coefficient of thermal expansion | |||
| MD | |||
| < 84℃ | 2.7E-5 | cm/cm/℃ | |
| > 84℃ | 8.8E-5 | cm/cm/℃ | |
| Thermal conductivity coefficient | 1.1 | W/m/K | ASTM F433 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 4.1E+13 | ohms | ASTM D257 |
| Volume resistivity | 2.6E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 13 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 100 Hz | 5.65 | ||
| 1 kHz | 5.57 | ||
| 10 kHz | 5.46 | ||
| 100 kHz | 5.34 | ||
| Dissipation factor | |||
| 100 Hz | 0.010 | ||
| 1 kHz | 0.010 | ||
| 10 kHz | 0.010 | ||
| 100 kHz | 0.010 |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| colour | |||
| — | Black | ||
| — | Clear/Transparent | ||
| Weight Mix Ratio (PBW) | |||
| Resin | 100 | ||
| Hardener | 4.1 | ||
| Volume Mixing Ratio (PBV) | |||
| Resin | 9.7 | ||
| Hardener | 1.0 | ||
| Density | |||
| — | 0.958 | g/cm³ | |
| — | 2.39 | g/cm³ | |
| viscosity | |||
| 25℃ | 0.055 | Pa·s | |
| 25℃ | 18 | Pa·s | |
| 25℃ | 120 to 200 | Pa·s | |
| Gelation time | |||
| 25℃ | 1.5E+2 | min | |
| storage stability | |||
| 25 ℃ | 80 | min |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Resin |
| 3. Hardener |
| 4. Hardener, Spindle #1 @ 20 rpm |
| 5. Mixed, Spindle #6 @ 20 rpm |
| 6. Resin, Spindle #7 @ 20 rpm |
| 7. 400 g mass |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |